46Cr2
2018-01-29 16:56:55
We are a professional manufacturer of 46Cr2, we can provide the third party inspection report and datasheet of 46Cr2 as round bar, square bar, flat steel and so on. Please send the inquiry to us if you are if you are interested in 46Cr2. We will serve you with honesty, integrity, and professional. The detail data as below follow:
Steel Grade: 46Cr2| Material No.: 1.7006
CHEMICAL COMPOSITION(46Cr2):
C(％) : 0.42～0.50
Si(％) : ≤0.40
Mn(％) : 0.50～0.80
P(％)≤: 0.035
S(％)≤: 0.035
Cr(％) : 0.40～0.60
Mo(％) : —
Ni(％) : —
HARDNESS AND HEAT TREATMENT(46Cr2):
Quench/℃|Water: 820～850
Quench/℃|Oil: 830～860
Temper/℃: 550～660
MECHANICAL PROPERTIES④ (46Cr2):
Softening Annealing/℃
: 650～700
Tensile Strength(≤100mm)|σb/MPa②③: 670
Reduction of Area(≤100mm)|ψ(％)②③: 54
Tensile Strength(≤60mm)|σb/MPa②④: 650
Reduction of Area(≤60mm)|ψ(％)②④: 56
Tensile Strength≥|σb/MPa⑥: 780～930
Yield Strength≥|σs/MPa⑥: 540
Extensibility≥|δ5(％)⑥: 14
Reduction of Area≥|ψ(％)⑥: 45
Ballistic≥|AKV/J①⑥: 41
Remark(46Cr2):
①, The test sample is according to DVM-V.
②, It is mechanical properties for cold upsetting and cold extruding.
③, It is softening annealing.
④, It is cold-drawing softening annealing.
⑤, The standard is DIN 1654(1989).
⑥, It is mechanical properties after hot working.
Introduction structural steel (46Cr2)
Structural steel is a steel that conforms to a specific strength and formability grade. The formability is expressed as the elongation at the end of the tensile test. Structural steel is generally used for bearing and other purposes. In these uses, the strength of steel is an important design standard.
Most steels used throughout Europe are specified to comply with the European standard EN 10025. However, many national standards also remain in force.
Typical grades are described as 'S275J2' or 'S355K2W'. In these examples, 'S' denotes structural rather than engineering steel; 275 or 355 denotes the yield strength in newtons per square millimetre or the equivalent megapascals; J2 or K2 denotes the materials toughness by reference to Charpy impact test values; and the 'W' denotes weathering steel. Further letters can be used to designate fine grain steel ('N' or 'NL'); quenched and tempered steel ('Q' or 'QL'); and thermomechanically rolled steel ('M' or 'ML').
Application(46Cr2)
Structural steel is a category of steel used for making construction materials in a variety of shapes. Many structural steel shapes take the form of an elongated beam having a profile of a specific cross section. Structural steel shapes, sizes, chemical composition, mechanical properties such as strengths, storage practices, etc., are regulated by standards in most industrialized countries.
HOT SALE:
SA-675GR70, SA-387GR91, X6NiCrTiMoVB25-15-2, 17-4PH, 15-5PH,
ASTM 630, X3CrNiMo13-4, UNS41500, X10CrNiTi18-10, S17400,
X5CrNiCuNbl6-4, 316Ti, 301A, 303, 304L, 310S, 316L, 317L, 321,
NKA80, DIN 1.4731, DIN 1.4021, DIN 1.4016, DIN 1.4571, DIN 1.4418,
616, 440B, 440C, 431, 430FR, 430F, 430, 422, 416, 410, 405,
ASTM D2, X155CrMoV12-1, ASTM D3, AISI H11, AISI H13, 46Cr2
Steel Grade: 46Cr2| Material No.: 1.7006
CHEMICAL COMPOSITION(46Cr2):
C(％) : 0.42～0.50
Si(％) : ≤0.40
Mn(％) : 0.50～0.80
P(％)≤: 0.035
S(％)≤: 0.035
Cr(％) : 0.40～0.60
Mo(％) : —
Ni(％) : —
HARDNESS AND HEAT TREATMENT(46Cr2):
Quench/℃|Water: 820～850
Quench/℃|Oil: 830～860
Temper/℃: 550～660
MECHANICAL PROPERTIES④ (46Cr2):
Softening Annealing/℃
: 650～700
Tensile Strength(≤100mm)|σb/MPa②③: 670
Reduction of Area(≤100mm)|ψ(％)②③: 54
Tensile Strength(≤60mm)|σb/MPa②④: 650
Reduction of Area(≤60mm)|ψ(％)②④: 56
Tensile Strength≥|σb/MPa⑥: 780～930
Yield Strength≥|σs/MPa⑥: 540
Extensibility≥|δ5(％)⑥: 14
Reduction of Area≥|ψ(％)⑥: 45
Ballistic≥|AKV/J①⑥: 41
Remark(46Cr2):
①, The test sample is according to DVM-V.
②, It is mechanical properties for cold upsetting and cold extruding.
③, It is softening annealing.
④, It is cold-drawing softening annealing.
⑤, The standard is DIN 1654(1989).
⑥, It is mechanical properties after hot working.
Introduction structural steel (46Cr2)
Structural steel is a steel that conforms to a specific strength and formability grade. The formability is expressed as the elongation at the end of the tensile test. Structural steel is generally used for bearing and other purposes. In these uses, the strength of steel is an important design standard.
Most steels used throughout Europe are specified to comply with the European standard EN 10025. However, many national standards also remain in force.
Typical grades are described as 'S275J2' or 'S355K2W'. In these examples, 'S' denotes structural rather than engineering steel; 275 or 355 denotes the yield strength in newtons per square millimetre or the equivalent megapascals; J2 or K2 denotes the materials toughness by reference to Charpy impact test values; and the 'W' denotes weathering steel. Further letters can be used to designate fine grain steel ('N' or 'NL'); quenched and tempered steel ('Q' or 'QL'); and thermomechanically rolled steel ('M' or 'ML').
Application(46Cr2)
Structural steel is a category of steel used for making construction materials in a variety of shapes. Many structural steel shapes take the form of an elongated beam having a profile of a specific cross section. Structural steel shapes, sizes, chemical composition, mechanical properties such as strengths, storage practices, etc., are regulated by standards in most industrialized countries.
HOT SALE:
SA-675GR70, SA-387GR91, X6NiCrTiMoVB25-15-2, 17-4PH, 15-5PH,
ASTM 630, X3CrNiMo13-4, UNS41500, X10CrNiTi18-10, S17400,
X5CrNiCuNbl6-4, 316Ti, 301A, 303, 304L, 310S, 316L, 317L, 321,
NKA80, DIN 1.4731, DIN 1.4021, DIN 1.4016, DIN 1.4571, DIN 1.4418,
616, 440B, 440C, 431, 430FR, 430F, 430, 422, 416, 410, 405,
ASTM D2, X155CrMoV12-1, ASTM D3, AISI H11, AISI H13, 46Cr2
